NREL’s New Perovskite Ink Opens Window for Quality Solar Cells

Scientists have developed a new perovskite ink with a long processing window that allows the scalable production of perovskite thin films for high-efficiency solar cells.


Scientists at the U.S. Department of Energy’s (DOE) National Renewable Energy Laboratory (NREL) developed a new perovskite ink with a long processing window that allows the scalable production of perovskite thin films for high-efficiency solar cells.

Proven highly efficient at converting sunlight into electricity, perovskite solar cells have yet to move beyond the laboratory. The crystalline structure of perovskites must be carefully grown upon a substrate, which is normally done by laboratory-scale spin coating — a technology that can’t be scaled to large-scale manufacturing.

The best devices fabricated using scalable deposition methods, which are suitable for future module production, still lag behind state-of-the-art spin-coated devices.

perovskite ink
Samples of solar cells grown using a new perovskite ink. Photo by Dennis Schroeder.

How the NREL scientists overcame this obstacle is spelled out in a new paper published in Nature Energy, Perovskite ink with wide processing window for scalable high-efficiency solar cells. Kai Zhu, a senior scientist in NREL’s Chemistry and Nanoscience Center, is lead author. The co-authors are Mengjin Yang, Zhen Li, Matthew Reese, Obadiah Reid, Dong Hoe Kim, Sebastian Siol, Talysa Klein, Joseph Berry, and Michael van Hest from NREL, and Yanfa Yan from the University of Toledo.

To create a perovskite film, a coating of chemicals is deposited on a substrate and heated to fully crystalize the material. The various steps involved often overlap with each other and complicate the process. One extremely critical stage requires the addition of an antisolvent that extracts the precursor chemicals, and thus create crystals of good quality. The window for this step opens and closes within seconds, which is detrimental for manufacturing due to the precision required to make this time window.

NREL researchers were able to keep that window open as long as 8 minutes.

The formula for the precursor perovskite ink included a chlorine-containing methylammonium lead iodide precursor along with solvent tuning, coupled with an antisolvent, which could be deposited onto the substrate by either spin-coating or blade-coating methods. Both methods were tested and produced indistinguishable film morphology and device performance. Blade-coating is more attractive to manufacturers because it can easily be scaled up.

The researchers tested one precursor ink containing excess methylammonium iodide (MAI) and a second containing added methylammonium chloride (MACI). The MACI proved most effective in reducing the length of heat treatment the perovskites require, cutting the time to about a minute compared to 10 minutes for the MAI solution. The shorter time also should make the process more attractive to manufacturers.

Using blade-coated absorbers, NREL scientists made a four-cell perovskite module measuring about 12.6-square centimeters. Of that, 11.1-square centimeters were active in converting sunlight to energy and did so with a stabilized efficiency of 13.3 percent.

Reference(s):
1. Publication: Mengjin Yang, Zhen Li, Matthew O. Reese, Obadiah G. Reid, Dong Hoe Kim, Sebastian Siol, Talysa R. Klein, Yanfa Yan, Joseph J. Berry, Maikel F. A. M. van Hest, Kai Zhu. Perovskite ink with wide processing window for scalable high-efficiency solar cells. Nature Energy, 2017
2. Research story: DOE/National Renewable Energy Laboratory | April 18, 2017 (source)

Leave a Reply

What to Read Next:

How bubbles form, could lead to smaller lithium-air batteries

With about three times the energy capacity by weight of today's lithium-ion batteries, lithium-air batteries could one day enable electric...

Solar cell design with over 50% energy-conversion efficiency

Solar cells convert the sun’s energy into electricity by converting photons into electrons. A new solar cell design could raise...

Researchers have developed a breakthrough alternative to fire-prone lithium-ion batteries

Joseph Parker, Jeffrey Long, and Debra Rolison from NRL's Advanced Electrochemical Materials group are leading an effort to create an...

Thin Layers of Water Hold Promise for the Energy Storage of the Future

Researchers at North Carolina State University have found that a material which incorporates atomically thin layers of water is able...

Australian solar industry sets new record

The Australian Photovoltaic Institute (APVI), with data from the Clean Energy Regulator, says the country has a new solar energy...